Prerequisites for installation and use:

• Enki Application

* Prerequisites for the Enki application: Internet access and a phone with a minimum operating system: Android: 7 / iOS: 15

Communication protocol:

• Cloud

Available countries:

• France

State feedback available: 

• Yes

Alexa voice control: 

• Not direct, but possible via manual scenarios

Google Home voice control: 

• Not direct, but possible via manual scenarios

Article contents:

• Technical description

• Product functionality in the ENKI application

• Product view

• What does the LED status of my product mean?

• How to reset my device?

• Technical documents / user manual

Technical description:

• Type: Connected control center for electric pergola with adjustable slats
• Requires Enki box: No
• State feedback: Yes
• Radio protocol: IO
• Radio frequency: 868 - 870 MHz, < 25 mW
  • Radio range in open field: 80 m
• Native application: TaHoma by Somfy
• Gateway required and recognized by Enki:
  • TaHoma Switch
  • Connectivity kit
  • TaHoma DIN-Rail / TaHoma Rail-DIN S
  • TaHoma Premium
  • Connexoon
• Power supply: 24 Vdc SELV
• Frequency bands and maximum power used:
  • 868.000 MHz - 868.600 MHz e.r.p. <25 mW
  • 868.700 MHz - 869.200 MHz e.r.p.<25 mW
  • 869.700 MHz - 870.000 MHz e.r.p. <25 mW
• Protection rating: IP 65
• Electrical insulation: Class 3 (SELV 24V)
• Operating temperature: -20 °C to +60 °C
• Dimensions (L x W x H): 99 x 185 x 57 mm
• Maximum number of control points and associated sensors:
  • 3 maximum control points
  • 9 maximum sensors
• Power supply: DC - RGE 11 - 24V
• Standby consumption: 0 W
• Maximum power: 288 W
• Current depending on switch 3: 2 x 3 A or 2 x 5.5 A
• Color/Finish: Gray

Product functionality in the ENKI application:

Control page	Settings

Product view:

1 - Power input A -  24 Vdc Power input (SELV) B + 2 - Motor output 1 C -  24 Vdc Motor - 3A/5.5A: Max current depending on switch 3 D + 3 - Motor output 2 E -  24 Vdc Motor - 3A/5.5A: Max current depending on switch 3 F + 4a - Motor without encoder 4b - Motor with HALL encoder Motor encoder input (Switch 1 = ON) G ↑  Encoder input (ILS or HALL) motor 1 H ↓  Encoder input 2 (ILS or HALL) motor 1 I -  Power output: 24 Vdc - 300mA Max J + K ↑  Encoder input 2 (ILS or HALL) motor 2 L ↓  Encoder input (ILS or HALL) motor 2 M -  Power output: 24 Vdc - 300mA Max N + 5 - Rain sensor O Contact  Dry contact input P Common 6 - Power output Q -  Power output: 24 Vdc - 300mA Max R + 7 - External antenna S Signal  Core T GND  Shield braid 8 - PROG button Switches: Int 1 ON  Motor with encoder sensor OFF  Motor without encoder sensor Int 2 (only if switch 1 is ON) ON  Activates synchronization S1 and S2 OFF  Deactivates synchronization S1 and S2 Int 3 ON  5.5 A max per output OFF  3 A max per output Int 4 ON  Activates temperature sensor OFF  Deactivates temperature sensor Int 5 ON  Closure in case of wind OFF  Opening in case of wind

What does the LED status of my device mean:

Status  The LED "flashes" every 4 seconds: Board waiting  The LED blinks rapidly: Command in progress. Fault  The red LED stays on for 5 seconds: Current consumption threshold exceeded or excessive heating of the electronic board during an output command.  The red LED blinks: motor synchronization fault.  The orange LED stays on for several seconds: memory saving.  The orange LED blinks rapidly: motor movement forbidden by a sensor action. Wind (1)  The orange LED stays on: wind threshold exceeded.  The orange LED blinks rapidly: protection still active for 15 minutes after the last threshold exceedance. Rain (1)(2)  The orange LED stays on: rain threshold exceeded.  The orange LED blinks rapidly: protection still active for 15 minutes after the last threshold exceedance. Temperature (1)(2)  The orange LED stays on: frost threshold exceeded.  The orange LED blinks rapidly: protection still active for 15 minutes after the last threshold exceedance.

Snow: Combination of rain and temperature information. (1): The proper functioning of the sensors depends on installation and maintenance conditions outdoors as close as possible to the pergola. Refer to the sensor manual before installation. (2) : The LED indicators will remain visible even if the sensors have been deactivated.

How to reset my device?

Perform a reset of my connected device
# Press and hold the "PROG" button on the electronic board. After seven seconds, all indicators will light up.
Press and hold the "PROG" button	After 7 sec. all indicators light up.
# Once all indicators are lit, release. The reset of the electronic board has been successfully completed.
When all indicators are lit, release. The reset is successfully applied.

Technical documents / user manual